Keea

Forum Replies Created

Viewing 12 posts - 1 through 12 (of 12 total)
  • Author
    Posts
  • March 22, 2019 at 3:41 pm #22853
    Keea
    Participant

    Thanks.  This resolved the issue.  There was a reference in the dashed line video that advised to set it to a solid line, but maybe I misunderstood.  Thanks for the help.  Condocs keeps on progressing.  Thanks to you all for a great plugin….

    March 22, 2019 at 3:41 pm #32149
    Keea
    Participant

    Thanks.  This resolved the issue.  There was a reference in the dashed line video that advised to set it to a solid line, but maybe I misunderstood.  Thanks for the help.  Condocs keeps on progressing.  Thanks to you all for a great plugin….

    March 20, 2019 at 9:42 pm #22819
    Keea
    Participant

    I have the SU and LO files I could email if you send me your email…thx, Keea

    March 20, 2019 at 9:42 pm #32144
    Keea
    Participant

    I have the SU and LO files I could email if you send me your email…thx, Keea

    March 20, 2019 at 9:41 pm #22818
    Keea
    Participant

    Thanks Luke.  That worked.  I am now having an issue with dash lines appearing as a solid line for my roof plan and foundation plan.  I did a test model following exactly Mike’s video tutorial on dash lines.  But it did not kick out the same results.  Can you look at my files and help me get this corrected?  much thx, Keea

    March 20, 2019 at 9:41 pm #32141
    Keea
    Participant

    Thanks Luke.  That worked.  I am now having an issue with dash lines appearing as a solid line for my roof plan and foundation plan.  I did a test model following exactly Mike’s video tutorial on dash lines.  But it did not kick out the same results.  Can you look at my files and help me get this corrected?  much thx, Keea

    February 22, 2019 at 5:35 pm #21949
    Keea
    Participant

    Could anyone point me to a possible tutorial or video I may have missed that shows the updated workflow for renovation plans, given the existing, new and demolished layers are now included in the layer set?  thanks, Keea

    February 22, 2019 at 5:35 pm #32105
    Keea
    Participant

    Could anyone point me to a possible tutorial or video I may have missed that shows the updated workflow for renovation plans, given the existing, new and demolished layers are now included in the layer set?  thanks, Keea

    November 9, 2018 at 4:56 am #19237
    Keea
    Participant

    That did it.  The more I am using Condocs and understanding it, the more I can’t believe I have worked without it.  Major upstepping for me.  Thanks so much, Keea

    November 9, 2018 at 4:56 am #32064
    Keea
    Participant

    That did it.  The more I am using Condocs and understanding it, the more I can’t believe I have worked without it.  Major upstepping for me.  Thanks so much, Keea

    October 30, 2018 at 9:14 pm #19108
    Keea
    Participant

    Hi Aaron,  I have been on the same quest to make my MacBook Pro work with Condocs consistently.  I opened your model on my computer and it crashed instantly when I ran Condocs section and elevation.  I can tell you what I have found that I am working with now until a more permanent solution comes is:

    • Start a clean project
    • run design and draft mode so Condocs layers come in
    • make basic model shape and layers, very simple and low poly count
    • add no textures, except solid colors from paint bucket tool.
    • run the section, elevation, perspective, details, and plan generator with full intention of your end product.  Do this as early on as possible. Condocs should work fine.  Then you will have everything set for export to LO.
    • After that, you should be able to model how you need to complete the design.  Simply save the model, update in LO and you will be good to go.

    I have found that textures were one of the leading causes of the crashes.  I just completed a full set of drawings this way, keeping conscious of my model geometry was the key.  It is not a fix, but was effective for me.  I too have had great results in SU with my MacBook Pro, as far as speed and what it can handle. It runs dual screens and I have been blown away by it’s performance.  Skalp and Condocs have had crashing issues.  I have disabled Skalp for now.  I do think Mike’s system is awesome.  Just hope to get a more permanent solution in place.  Thanks, Keea

    October 30, 2018 at 9:14 pm #32057
    Keea
    Participant

    Hi Aaron,  I have been on the same quest to make my MacBook Pro work with Condocs consistently.  I opened your model on my computer and it crashed instantly when I ran Condocs section and elevation.  I can tell you what I have found that I am working with now until a more permanent solution comes is:

    • Start a clean project
    • run design and draft mode so Condocs layers come in
    • make basic model shape and layers, very simple and low poly count
    • add no textures, except solid colors from paint bucket tool.
    • run the section, elevation, perspective, details, and plan generator with full intention of your end product.  Do this as early on as possible. Condocs should work fine.  Then you will have everything set for export to LO.
    • After that, you should be able to model how you need to complete the design.  Simply save the model, update in LO and you will be good to go.

    I have found that textures were one of the leading causes of the crashes.  I just completed a full set of drawings this way, keeping conscious of my model geometry was the key.  It is not a fix, but was effective for me.  I too have had great results in SU with my MacBook Pro, as far as speed and what it can handle. It runs dual screens and I have been blown away by it’s performance.  Skalp and Condocs have had crashing issues.  I have disabled Skalp for now.  I do think Mike’s system is awesome.  Just hope to get a more permanent solution in place.  Thanks, Keea

  • Author
    Posts
Viewing 12 posts - 1 through 12 (of 12 total)